Uqmi openwrt. I've added interface 4G via luci using QMI Cellular mode.

Uqmi openwrt It's 4G-modem works fine with stock firmware, but I need OpenWRT. ) TX: 0 B (0 Pkts. 0 DISCLAIMER: once I installed openwrt on the tp-link WR6400 v5, i haven’t been able to reinstall the original TP-link firmware! I spent few hours to get a working connection via SIM card, and did try few configuration, before I had a working LTE connection. I dont seem to be able to connect OpenWRT as a client to my mobile hotspot. 3 and have setup my 4G Connection with uqmi Version uqmi_2022-05-16-0. org/project/uqmi. I purchased a TP-LINK MR6400 V5 installed Openwrt and Luci. org> 5 * 6 * This library is free software; you can redistribute it and/or 7 * modify it under the terms of the GNU Lesser General Public 8 * License as published by the Free Software Foundation; either 9 * version 2 of the License, or Hello, after reading a lot of things in this forum and trying very many variations I still cant get my Quectel EC 35E LTE modem zu make a connection while beeing abroad (Roaming). for your help Uqmi always reconnect/activate internet connection. root@OpenWrt:~# opkg install kmod-usb-serial kmod-usb-serial-option kmod-usb-serial-wwan [MIRROR] Tiny QMI command line utility. 5 to 2 days until it looses its DHCPv4 lease for WWAN_4 and even uqmi has parameter -t to set response timeout but there are two problems. 1 /* 2 * uqmi -- tiny QMI support 2014-2015 Felix Fietkau <nbd@openwrt. ncompact February 9, 2024, 9:24am 21. free disk space is 2. If I test at the I have successfully compiled modem manager into a 4. A 3G modem can register without an APN. com/mrhaav/openwrt-packages/blob/main/README. In the syslog I get: Mon Jan 28 12:41:34 2019 daemon. 9 But still the same segmentation fault: Tue Nov 22 10:31:36 2022 daemon. Is there any way to unable it? Thank you in a Hello. If you type any uqmi command and get no output, you may need to edit the qmi. My connection is rock-steady but anyways i wanted to check my strength to maybe improve the location of my router a bit more. Currently running: [Powered by LuCI openwrt-18. It hacks around the issue that uqmi can't read return Can use AT commands but no uqmi - OpenWrt Forum Loading After recently porting a ZTE MF286[,A,R] family support to OpenWrt, i decided to play around with IPv6 support - however I stumbled upon a strange issue. The situation is quite simple: modem (Quectel EC25-E Mini PCIe module) is recognised and seen as /dev/cdc-wdm0 out of the box. when i try to talk to the device using uqmi, i don't get any response! uqmi -d /dev/cdc-wdm0 --get-imei (command hangs) it has to do with the DTR, found a patch for the device on this forum: Hi there, I have a flashed a former three network branded router with Openwrt and setup an interface "lte" in /etc/config/network as described in the wiki. This is what the wireless menu and the status page looks like after a few Previous message (by thread): [PATCH 1/5] uqmi: support C reserved keywords in upstream JSON files Next message (by thread): [PATCH 5/5] uqmi: print radio interfaces in serving system command Messages sorted by: * Add 5G NR to supported networks in DMS --get-capabilities. name> [add command line help] 7 years ago mbim: fix memory corruption issues Hi 🙂 I'm lost I have a TP-Link LT-MR6400 v4 I successfully installed OpenWRT ( 22. 361. 05 Modem: HUAWEI E392 (Vendor=12d1, ProdID=1506, chipset=Qualcomm MDM9600) I've followed the guide on How To Use LTE modem in QMI mode for WAN connection When I If you want to contribute to the OpenWrt wiki, please post HERE in the forum or ask on IRC for access. 90. I've stumbled upon a weird issue with my SIM and the MBIM interface. g. 4M , i need install modemmanager to start LTE module, but it's 2. uqmi commands output: uqmi -d /dev/cdc-w I'm attempting to use QMI on a GL. 4GHz and 5GHz, cant use a password on the hotspot because OpenWRT needs wpa-supplicant for that, so I went with open (no password). Solved the problem, [MIRROR] Tiny QMI command line utility. Done a couple of re-installation but still no luck. conf. ) Error: Network device is not present I have installed the following QMI packages: kmod-usb-net-qmi-wwan uci-proto-qmi uqmi I can Hi I've been struggling to install my PCI-E MC7455 modem. I’ve enabled ppp & qmi mode with the following over ttyUSB2: AT+QCFG="usbnet",0 This makes the device show up as /dev/cdc For EC25 just use. Dont go with Luci-protocol-qmi. 4 kernel #6801. I've used LuCi and the QMI protocol in it to configure the thing. git: git Next message (by thread): [OpenWrt-Devel] Unable to connect with uqmi ("No effect") Messages sorted by: Hello, Hope this is the right place to ask for help and my apologies if it is not. Switches: uci set network. Post #11. I'm testing uqmi with a Telit LE910 LTE modem on Ubuntu 16. I use custom open wrt 23. 02. It seems that it terminates the inner thread in uqmi but the whole executable hangs indefinitely; I have created wrapper script replacing uqmi which calls original uqmi with Basically, uqmi and qmicli will most probably be able to do same but, for one thing, today I installed qmi-utils which filled up my entire /overlay due to various dependencies. org Cross Reference • source navigation • identifier search • freetext search • Sources/uqmi/ Parent directory: common/ data/ uqmi/ CMakeLists. 8 (x86 Geode) and ancient 3G USB modem Huawei E1820. Output ps: # ps 1798 root 1220 S udhcpc -p /var/run/udhcpc-wwan0. I got it to the point where it's connected, but I don't get an IP address automatically. The program will check every 30 seconds if there is a file into the send directory and eventually save received SMS messages from the modem memory to the received directory: I have set up a qmi celular card in my router I can run minicom and it has interfaces in dev but i cant get it to connect to the internet. OpenWrt Forum Qmi proto not get ipv6 in wan interface. Compiling: If you don´t find uqmi with desciption: Control utility for mobile broadband modems, mod by mrhaav in make menuconfig you need to "override" official uqmi. It does not seem to be stable for me and its not an official package yet. txt: 2771 bytes: qmi-errors. dnsleaktest. org> 5 * 6 * This library is free software; you can redistribute it and/or 7 * modify it under the terms of the GNU Lesser General Public 8 * License as published by the Free Software Foundation; either 9 * version 2 of the License, or 1 /* 2 * uqmi -- tiny QMI support 2014-2015 Felix Fietkau <nbd@openwrt. My need is a modem with 4G to use it predominantly only with LTE connection. Contribute to openwrt/uqmi development by creating an account on GitHub. 5-bcm27xx-bcm2710-rpi-3-squashfs-factory image file to microSD card. The bug reference is here I’m facing a problem on two routers WG3526 (Modem EC-25) and D-Link DWR921 (Model Broadmobi BM806). Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4. To do so you can plug the WAN port to a router. This seems to be a QMI device. OpenWrt 22. In my home this network is weak. And no the section looks like the following in the configuration file /etc/config/network: It is not required to set dhcp options for this interface because openwrt system does it by default. sh and the default value is infinite; timeout parameter does not work in some cases. I'm unsure about whether an IP address was shown or not, I shall check that next time it happens. Even if this isn't my first OpenWRT router, I'm new with this distro. komeilkma August 20, 2019, 8:00am 2. From what I understand, it is modifying the return message from the modem to always be "raw-ip", which is the only thing these modems support. And the existance of a luci package for it that I've got OpenWrt running fine so far, the only issue is the modem, which is a Qualcomm modem (same as in the v4). 180 linux kernel. I`m using LuCi to configure it. h: 23367 bytes: This page was automatically generated by LXR 0. sh. sh script to fix it. When i put SIM card in my phone and manual select network t openwrt-bot opened this issue Mar 19, 2017 · 7 comments Closed FS#641 - Quectel ECXX and Raw IP on 4. 3. in the meantime, thanks for the support I receive, I am in the evaluation and testing phase (connectivity permitting) mkrle February Hi folks, I have a problem trying to setup LTE modem in MR6400 v5. This is logs of what happens when I click on "connect" button on this interface (called "qmi_wwan0" ) Sun May 27 09:47:43 2018 daemon. wan netw description: Tiny QMI command line utility: owner: Git: last change: Sun, 25 Aug 2024 00:36:21 +0000 (02:36 +0200): URL: https://git. org> 5 * 6 * This library is free software; you can redistribute it and/or 7 * modify it under the terms of the GNU Lesser General Public 8 * License as published by the Free Software Foundation; either 9 * version 2 of the License, or OpenWrt. After change to standard firmware for v5, I've installed luci-qmi-proto-app. root@OpenWrt:/# cat /etc/config/network config interface 'loopback' option device 'lo' option proto 'static' option ipaddr '127. Whenever doing reboots, it was noticeable that the module won't accept AT commands unless this process "uqmi -s -d /dev/cdc-wdm0 --wda-get-data-format" is manually terminated then everything will proceed fine. Don't patch it manually since the fix is already there. notice netifd: qmi_wwan0 (3998): "Unknown error" Sun May Good Day, As a noob I've been very impressed by how to much detailed knowledge there is on technical details associated with getting a LTE modem to work. . I'm using uqmi to verify everything before configuring a new wwan interface. before i was stuck here, now i moved to another country and i am able to register to the network. The driver is installed, cdc and ttyUSBx exposed rightfully. My proposal is: Set the modem in flight mode uqmi -d /dev/cdc-wdm0 --set-device-operating-mode low_power Configure the default APN profile OpenWrt 18. \\ \\ I really like QMI - I have been using those modems a lot in OpenWRT 22. notice netifd: wwan (4272): + uqmi -s -d /dev/cdc-wdm0 --stop-network 0xffffffff --autoconnect Fri Dec 16 15:58:51 2022 daemon. 03. 06 branch (git-19. So I decided to collect as much information as possible and make a topic about it here in hopes of getting some help and maybe the one hint that I am probably still missing My OpenWRT is uqmi: Add sync command to release all cids. 02 I think), but after upgrading to 23. Signed-off-by: David Bauer <mail@david-bauer. Can anyone please give me a hint to get through this problem. Latest version: 2022-11 I think the best way to configure an LTE modem is to use APN profiles. If you need some special uqmi command to be exequted every 30s, add them to the daemon, /usr/bin/uqmi_d. 3 r20028-43d71ad93e ) on this router. notice netifd: LTE (4097): PINcode disabled Tue Nov 22 11:39:08 2022 daemon. The modem is connected and you do > not disconnect, so "start-network" has no effect. Hello everybody I installed OpenWrt 21. org> 5 * 6 * This library is free software; you can redistribute it and/or 7 * modify it under the terms of the GNU Lesser General Public 8 * License as published by the Free Software Foundation; either 9 * version 2 of the License, or I've stumbled over "Failed to open device", too. I followed this guide: I sent "opkg install usb-modeswitch kmod-mii kmod-usb-net kmod-usb-wdm kmod-usb-net-qmi-wwan uqmi" I installed luci-proto-qmi but i can't see any config. I made these settings, but only the first light of the signal strength stays on and does not display the strength of the antenna. 05, the connection always returns PIN_STATUS_FAILED. I've tried to use uqmi package from @mrhaav uqmi_2022-04-22-0. How to use LTE modem in QMI mode for WAN connection Some new 3G/4G dongles use qmi and mbim protocol to I have a TP-Link TL-MR6400 v5. Scroll to the bottom for the issue description. First time uqmi command might hang. org> 5 * 6 * This library is free software; you can redistribute it and/or 7 * modify it under the terms of the GNU Lesser General Public 8 * License as published by the Free Software Foundation; either 9 * version 2 of the License, or I used luci-proto-qmi to set up a LTE connection. ipk from mrhaav . sh When I run: #uqmi -s -d /dev/sdc-wdm0 --get-pin-st Installing and Using OpenWrt. Modem has the following firmware: root@OpenWrt:~# socat - /dev/ttyUSB2,crnl ATI Quectel EC25 Revision: EC25EFAR06A06M4G OK. 5_mipsel_24kc. I tried to find the built in modem at the interface of Luci but there wasn't anywhere. A 3G uqmi is a command line tool for controlling mobile broadband modems using\\ the QMI-protocol. 05 and uqmi module for LTE connectivity and it works quite well. Every 12 hours my ISP change the IP of the 30 uqmi is a command line tool for controlling mobile broadband modems using Router: TL-WR1043N v2 OpenWRT: Chaos Calmer 15. 0' config globals 'globals' option ula_prefix 'fd64:9999:eeea::/44' #I changed the numbers a lite idk if it is important config device option Hi! I have problem after install OpenWrt on D-Link DWR-921 My SIM Card - Mobile Viking - Poland operator using Play signal. Both auth and pdptype are listed as optional in the docs though. " I did pick up the QMI protocol is rather new, and for a while we had to set it to NDIS mode, but I was under the impression it was fully implemented by now. However, the same option works fine with the DHCP protocol, which is partially used by uqmi. 02 > On openwrt-19. 06. with a router. 2 router. OpenWrt Wiki – 3 Jan 15 How to use LTE modem in QMI mode for WAN connection. Modem-manager Hello. Then I've built firmware with modem-manager without LUCI, because it doesn't fit it space. Looking at the network interfaces screen I can see: Protocol: QMI Cellular RX: 0 B (0 Pkts. 1 Next message (by thread): [OpenWrt-Devel] Unable to connect with uqmi ("No effect") Messages sorted by: Hi Bjørn, thanks for the reply > AFAICS, that is the expected result. The modems are not able to handle multiple uqmi request at the same time. lobrano at gmail. For example, this is the response I get if I issue the command "at!gstatus?" to the Having ongoing issues, I inserted set -x into qmi. Basically, this is a combination of MF281 and MF286, both already supported. If the signal strength script and the LuCI status page code call it at the same time I followed the following steps: Flashed the openwrt-22. I've 1 /* 2 * uqmi -- tiny QMI support 2014-2015 Felix Fietkau <nbd@openwrt. Boot the RPI 3 board Initially IP is set as static so I changed it to DHCP client to connect to internet to download pakages. Inet MiFi equipped with a Quectel EC-25A cellular modem. kpv. Being openwrt, it is proving to I set up a Sierra Wireless MC7354 LTE modem on the ~latest OpenWRT build. However I'm now having a hard time "properly" shutting down a network connection (without pdh). 05. Can someone point me to a tutorial? Thanks in > > yes that would not be bad at least for openwrt-21. Your kennel should be Linux OpenWrt 4. The DNS servers provided by the ISP are always added to /tmp/resolv. com> writes: >> AFAICS, that is the expected result. Git; Hy everyone, First of all this setup worked 2 years ago like charm. 2 router to log signal data that uqmi doesn't provide. Tried with 2. I'm using latest snapshot because I Customized uqmi with APN profiles. The standard configuration can be used, but DHCP (for IPv4) should be disabled, either in Luci or in the configuration file (/etc/config/network): . notice netifd: Interface 'LTE' is setting up now Tue Nov 22 11:39:07 2022 daemon. ) I'm running the latest openwrt so no issues there. Downloaded the following packages: kmod-usb-net-qmi-wwan uqmi luci-proto-qmi kmo libc, uqmi Categories: luci---protocols Repositories: luci Architectures: If you want to contribute to the OpenWrt wiki, please post HERE in the forum or ask on IRC for access. ssh root@192. Signed-off-by: Nickolay Ledovskikh <nledovskikh@gmail. Enable other required network drivers. Then, successfully connected to the LTE network using uqmi CLI tool. Installing and Using OpenWrt. Yes, but that's for the case of half-assed ISP implementations, which do dual-stack using dual APNs. Then I am simply I noticed that setting 'option peerdns 0' with qmi protocol (uqmi package) has no effect. So I get encouraging answers and finally has cdc device ~# ls -l /dev/cdc-wdm0 crw------- 1 root root 180, 176 Jul 29 11:37 1 /* 2 * uqmi -- tiny QMI support 2014-2015 Felix Fietkau <nbd@openwrt. notice netifd: Lte (2201): "No effect" On turris omnia, after a random disconnection of the Quectel OpenWrt and QMI mode LTE QUECTEL EC25-E RAW-IP Loading I have a Quectel EC25-E and a sim card but for some reason it's failing to connect, the apn details are correct. For now, I have the following script run by cron every minute to "fix" it: Hi friends I installed openwrt 18. 07, unless uqmi support is really broken. 02 freshly installed that I've seen some people installed I followed the solution in this topic. 1 I am getting the following version of "uqmi - 2023-10-29-eea29240-1" but I cant find this as a package that I can install on my other devices to see if that fixes my problems ? I also cant find this "latest version" for download, have checked here: OpenWrt Wiki – 5 Nov 23 package: uqmi. net> 12 days ago uim: fix help formatting Autoconnect is by default 1 in uqmi: OpenWrt Wiki – 3 Jan 15 How to use LTE modem in QMI mode for WAN connection. I'll start by explaining the background, how the issue looks like and what I suspect the problem is. Hi I think the best way to configure an LTE modem is to use APN profiles. Uqmi considers the modem connected from the very beginning On 21. 4 r7808 Hello everyone, I've been struggling at connecting my 3G/4G modem with a private APN. Let me know if it works. In Germany it works fine, i set it up so once disconnected it will reboot and all fine. It's being detected as QMI device and AT commands work as well. Thank you in advance. 7M I tried flashing my mr6400 following instructions from officiall page: didn't work, tried doing it on windows 10 and linux (disculpeu-me per escriure en english) Openwrt version used: OpenWrt 23. Below is the output uci show network. So it is the pure WAN speed of the modem. 0. ipk How can i setup huawei e3372h LTE usb modem with TP-Link TL-WR902AC v3? I tried Rooter firmware and it detected the LTE modem without issues. org> 5 * 6 * This library is free software; you can redistribute it and/or 7 * modify it under the terms of the GNU Lesser General Public 8 * License as published by the Free Software Foundation; either 9 * version 2 of the License, or Hello, I have a usb dongle ZTE MF190 and I added a network interface in the web configuration using qmi cellular protocol but it does NOT work (Rx is 0 and Tx is 0), BUT WORKS like this: //run this cmds wds=uqmi -s -d 1 /* -*- Mode: C; tab-width: 4; indent-tabs-mode: nil; c-basic-offset: 4 -*- */ 2 /* 3 * libqmi-glib -- GLib/GIO based library to control QMI devices 4 * 5 * This library is free software; you can redistribute it and/or 6 * modify it under the terms of the GNU Lesser General Public 7 * License as published by the Free Software Foundation; either 8 * version 2 of the License, or (at your Contribute to openwrt-set/uqmi development by creating an account on GitHub. The MC7455 works just fine but when I'm trying to setup an EM7565 I can't get it work properly. ipk files to router using scp because even though I connected isp provided modem to the mr6400 so that i can get internet on mr6400 I can't update opkg repos or install packages even though I get internet connection and I can browse the web when connected to Recently I have had the joy of setting up OpenWrt on my shiny new 4G modem, namely a Zyxel NR7101, to replace my old Huawei B818-263 operating in bridge mode. After some research here in Italy, I found I have TP-Link TL-MR6400 v5. 3 r11063-85e04e9f46 which has 4. 9 kernel build but i am having issues with libqmi. I suspect it is trying to attatch to the incorect network but I dont know how to select the correct network. I don't know how much interest there is, but I've got initial Hello, I opened a bug on the OpenWRT bugtracking system but I'm quickly asking here if someone is also having this problem. usbmode The router is running OpenWrt 19. uqmi is a command line tool for controlling mobile broadband modems using\\ the QMI-protocol. I googled a little bit and found out that I'm not the only one having problems to connect to I have an GL-X750v2 (c6-e) Router (4g modem). Installing it using " How To use LTE modem in QMI mode for WAN connection" guide. With proper IPv4v6, the procedure is the same, except for using the same APN and profile index in both address families. My sim is from Poland its called "Virgin mobile" and i think the apn is fine. I have decided to try and get uqmi working instead. SSH to If you do such a LuCI app, I think it would make sense to include some other information provided by uqmi. But modem haven't start after QMI have been properly configurated. The approach taken by ROOter is a hacky set of scripts, but at least it works on a wider variety of modems. For Developers. If you are connecting via terminal, then just SSH to your LEDE/OpenWRT device using the following command, where 192. # uqmi -d /dev/cdc-wdm0 --get-serving-system { "reg Hey Folks, I have a Problem with the QMI protocol. I saw many threads about it (like this one [Solved]UQMI won't connect with Private APN), but since I need something more automated, the solution presented on the aforementioned post wasn't likely to work in my case. 10, but I'm facing this weird issue. I want it to show both the SIM card signal strength and the Wi-Fi connection status and the modem status. I pieced it together from some old docs, and I wasn't sure if having a non-aliased interface was the right Per topic, I'm trying to capture the output of AT commands sent to an LTE modem attached to an OpenWrt 18. I was lucky and after some manipulations I have able to set it's modem in qmi mode. OpenWRT device will need to access to internet. 1. <your interface>. i have tried the luci qmi proto and manually setting it up but i never get an ip on the interface. The modem is the same as in the MF283+. Initially I followed the instructions under "Basic configuration" in the installation instr Hi everyone, I’m trying to run a Quectel EC25-E (I’m in europe so this is the right modem) over QMI protocol. How can I install the picocom & uqmi packages (with all?! their dependencies) offline? How can I install the picocom & uqmi packages (with all?! their dependencies) offline? For example download some files to notebook and transfer them? (how / luci interface?) to the router to Hi, im on Openwrt 21. Also i do have to manually download the packages because no wan connection - LTE not working. I wish to connect to the spark network but it seems to indicate vodafone is "Currently_Serving" root@OpenWrt:~# uqmi -d 1 /* 2 * uqmi -- tiny QMI support 2014-2015 Felix Fietkau <nbd@openwrt. 07 there are additional commits needed. The same applies to external I'm trying to setup a Unielec U7621 board with an LTE module, and asking your suggestions for a problem I have using latest snapshot build (both downloaded and/or compiled by myself). ipv6profile=<ipv6 profile number> If you need an other APN for IPv6. But my ISP reconnects every 4 hours, and my router doesn't reconnect and loses connection. The first uqmi command get stuck, so I abort root@OpenWrt:/# uqmi -d Hey everyone, The last time I had to post on a router forum was back in the dd-wrt days! Anyway, I have a PC Engines APU3 and I built a custom image to take advantage of the ECC, multicore, gpio, and other features of the OpenWrt. 4_mipsel_24kc. org> 5 * 6 * This library is free software; you can redistribute it and/or 7 * modify it under the terms of the GNU Lesser General Public 8 * License as published by the Free Software Foundation; either 9 * version 2 of the License, or I managed to integrate a Quectel RM500Q-GL in an Raspberry Pi 4B running OpenWRT 21. uqmi shows connected and i get signals but i Web interface integration of uqmi is missing from OpenWrt right now, as well as support for ECM/NCM/MBIM-based modems (but I'm planning to work on them as well). uqmi: add slot number to uim-sim-status output Add the SIM-card slot-number to uim-sim-status output. openwrt. 7 TP link Archer C2 AC750. I bought a private ip from my ISP and can't connect with the private APN, only the dynamic IP APN works. 1' option netmask '255. According to Luci and the uqmi tool it now seems to have a working LTE connection but I am still not able to access the internet. Tony. Also, got the IP and right MTU (1500). 0 on a RaspberryPi 4B with a Sierra Wireless EM7455 in a usb enclosure, which is set to MBIM mode. ipk package. dms: Added command: --get-device-operating-mode Included in uqmi. How to use LTE modem in QMI mode for WAN connection Many of currently available 3G/4G/5G modems use QMI and/or MBIM protocol to interact with the host system, e. I am trying to setup an OpenWrt 22. 0 it only seems to work with the latest uqmi - that I cant find. Test has not be done via WiFi, but directly on the Pi. Ok, then I won't touch 19. I got horrible values with the command: uqmi -d /dev/cdc-wdm1 --get-signal-info My values when the router is indoors and also the usual place where the router is located the [MIRROR] Tiny QMI command line utility. For your information, QMI is a proprietary Hi everyone, I'm trying to run a Quectel EC25-E (I'm in europe so this is the right modem) over QMI protocol. Immediately to my mind come IMEI and IMSI: root@Lemon:~# uqmi -d /dev/cdc-wdm0 --get-imei "8667580xxxxx486" I recently installed Openwrt on a "Zyxel LTE5398-M904" I apologize in advance if the question might be trivial I ask if anyone might have suggestions and/or opinions that would allow better management I created a script that runs every minute it checks the connection with the command: uqmi -d /dev/cdc-wdm0 --get-data-status | grep "disconnected" I would like to But when I am downloading 23. First go to here and download the latest uqmi_<xxxxxxxxx>_mipsel_24kc. notice netifd: Lte (2201): UQMI works fine! Mon Jan 28 12:41:34 2019 daemon. Also, I never managed to make IPv6 work without using explicit AT commands. This is logs of what happens when I click 1. com I set up openwrt like this: Then this 1 /* 2 * uqmi -- tiny QMI support 2014-2015 Felix Fietkau <nbd@openwrt. config interface wwan option proto qmi option apn <your-apn> option device /dev/cdc-wdm0 dhcp option 0 is required for other modems that "do not have a dhcp server" and need to get IP from qmi parameters. notice netifd: Interface 'LTE' is now down Tue Nov 22 11:38:57 2022 daemon. When I configure the interface using QMI I am able to connect to the cellular network at the radio layer, however my wwan0 interface is not assigned an IP address. I found some instructions that suggest that I "edit the qmi. Hey, I followed the information from here to setup my LTE connection on my TP-Link TL-MR6400 v5 router. The modem is connected and you do >> not Hi. However it now works for me now even with autoconnect. auto. 3 r23809-234f1a2efa is installed on an ZTE MF286D using serial+TFTP. config interface 'wwan' option proto 'qmi' option device '/dev/cdc-wdm0' option apn 'internet' option pdptype 'ip' option dhcp '0' Try adding option pdptype, the values are IP (for IPv4), IPV6 (for IPv6) or IPV4V6 (for dual-stack). Yes, you're right, but why am I connected in the first place? uqmi. After a lot of poking around, it seems like the is a problem with the implementation of UQMI and /or qmi. 2. It seems this is an issue with the SIM being in roaming mode. 3 r20028-43d71ad93e / LuCI openwrt-22. More information about the openwrt-devel mailing list uqmi: Add sync command to release all cids. 170. I write everything so, maybe, it can be useful also for other users with the same hardware. The Problem i have is after my ISP is reseting the connection when ~24h have passed, the connection is not getting restored. org Cross Reference • source navigation • diff markup • identifier search • freetext search • source navigation • diff markup • identifier I'm trying to activate the LTE connection in my MR6400 v5. " Unfortunately, I don't know how to edit the script nor how to find it. komeilkma September 24, 2019, 6:45am 1. My problem is that I currently have two modules with the same characteristics but one of them doesn´t work properly. My 4G provider is Free Mobile a French mobile provider. Just like I did that for Orange Poland, which doesn't offer true dual-stack, only either IPv4 or IPv6+CLAT. ok i fixed the wan (eth1) issue, seems it switch the ports 1-4 in reverse now 4-1 only thing left to figure out is the gps, and what ports gpsd is supposed to open "/dev/ttyUSB0" doesnt seem to be it Once installed the uqmi package, there is a daemon process /usr/bin/uqmi_d. With ModemManager the connection to my Private APN works as expected, so no fault on ISP side. How do i fix the DNS leak in openwrt after your extended test here? https://www. If I try to establish connection: root@OpenWrt:/# uqmi -d /dev/cdc-wdm0 --start-network --apn internet --ke ep-client-id wds "Call failed" And the connection state: root@OpenWrt:/# Contribute to openwrt-set/uqmi development by creating an account on GitHub. 03 branch git-22. opkg update opkg install kmod-mii kmod-usb-net kmod-usb-wdm kmod-usb-net-qmi-wwan Hello, I'm upgrading a router from a MC7455 to the EM7565. See the comments below for the details. I need to open a new topic about this router/modem because I didn't find a good solution. I'm already using @mrhaav modified uqmi wh i want get imsi data in oopnwrt by uqmi command from quectel ec25 but after send this command : uqmi -d /dev/cdc-wdm0 --get-imsi result is "Not supported" How can I fix this problem? I've just installed the latest version of OpenWrt on my ZTE MF286D, everything seems to be working except the modem. sh which is responsible for sending and receiving SMS messages. I configured the WIFI and local DHCP, my devices can connect on the router, but I have no any 1 /* 2 * uqmi -- tiny QMI support 2014-2015 Felix Fietkau <nbd@openwrt. \\ \\ This recipe explains how to setup and configure OpenWrt for using 3G/4G/5G USB modems for WAN connection, using QMI or MBIM protocol. Except where otherwise noted, content on this wiki is licensed under the following license: Sim7600x 4G Hat on Raspberry pi4 does not start - OpenWrt Forum Loading SIM7600G-H not connecting to internet - OpenWrt Forum Loading I received a couple of 3 HuiTube devices that are ZTE MF282 LTE routers. They have a QCA9563 SoC, 128MiB RAM and 128MiB NAND. org> 5 * 6 * This library is free software; you can redistribute it and/or 7 * modify it under the terms of the GNU Lesser General Public 8 * License as published by the Free Software Foundation; either 9 * version 2 of the License, or Hi, sorry for rising this topic again, but having read all the topics regarding EC25 I didn't find the solution. config system option hostname 'OpenWrt' option For those interested, this is the patch I used, it's exactly the same thing iuncuim suggested above but now it is working with latest uqmi sources used in OpenWrt. How can I overcome this problem so that my router re-establishes the connection in a short time? I would like to avoid simple cron tab Hey everyone, I'm using openWRT 23. 69894-438c598 Thu Feb 2 09:50:36 2023 Now it states: uqmi 2022-09-13-0. The modem would connect to IPv4 APNs just fine, even using just the last configured settings, with nothing more, than this in /etc/config/network: config interface 'wan' option proto 'qmi' option device '/dev/cdc Hello everyone, Sorry for my grammar im not a native English. TL-MR6400 v4 - LTE modem for WAN connection - OpenWrt Forum Loading Hi, after some problems getting OpenWrt on this router (thanks to frollic and Leo-PL for help) I'm now configuring the router. In order to get an ip address, I have to do ifup wwan0; ifup wwan1; udhcpc -i wwan1. 32094-4d6d8bc) OpenWrt 18. I see permission denied when one of the commands tries to run. name> [add command line help] 6 years ago mbim: fix memory corruption issues Hi Everyone, I have an EP06-E LTE-A module paired with OpenWRT (R00ter to be specific). notice netifd: Lte (2201): killall: uqmi: no process killed Mon Jan 28 12:41:34 2019 daemon. I did post my setup here, so helping should be easier here then another thread, so you have my setup info, interface, etc. notice netifd: wwan (4272): + uqmi -s -d /dev/cdc-wdm0 --set-device-operating-mode online Fri Dec 16 15:58:51 2022 . git 2022-02-22. I've added interface 4G via luci using QMI Cellular mode. hi friends my isp dns support ipv6 and i can get ipv6 in other modems from my sim card but in openwrt in zbt-826 i active qmi protocol for get internet from modem ec25 and in uqmi i cant get ipv6 just show my ip v4 3ginfo gui (Info about 3G/LTE connection) - OpenWrt Forum Loading [MIRROR] Tiny QMI command line utility. md. All of packages described here was installed. Nobody has an idea about this? can help me ? @Bmork @jeff. An LTE modem must have a valid APN profile to be able to register to the cellular network. 1 is your LEDE/OpenWRT device’s IP address. sh, and got following error: Fri Dec 16 15:58:51 2022 daemon. This was working fine in the previous OpenWRT version (21. Connectivity/coverage is fine, roaming is activated on the simcard in general How do i activate it on the openwrt setting/conf? Thanks. 07 running on this device. Looks like usb-modeswitch doing it's job changing 12d1:1446 to 12d1:1 Hello Please guide me how to configure the LEDs of the TP-Link TL-MR6400 v5 modem. Install Package QMI Cellular Openwrt. Modem goes online and I have a connection etc. ATI shows Manufacturer: ZTE CORPORATION Model: MF286DMODULE Revisi uqmi -d /dev/cdc-wdm0 --get-data-status: this command just stalled until ctl-C and any other commands that start with uqmi just stalled until ctl-C. 07. Network Scan works and sees my hotspot P20Pro. I think my qmi protocol hasnt been properly configured and activated. komeilkma August 16, 2019, and i check that gsm modem ipv6 is active how i can active ipv6 in qmi cellular proto interface ? Add ipv6 to uqmi openwrt. There is some time uqmi tries to reconnect but it ends with REGISTRATION_FAILED and i have to Old thread for reference: So yes it is straightforward to write a script to poll uqmi --get-signal-info to turn LEDs on or off based on the received signal strength on a QMI modem. Just cancel it and try to fire the second it will pass 🙂 Hy there, i have a problems making a connection with the LTE Modem. The integrated LTE modem is in QMI mode. Hardware: APU2C4 with mSata The Topic describes the problem really good. But then a problem occurs: I also have to work around a bug in uqmi: It does not lock the device it is working with. You shall double check it using editing the source file. NOTE: This device does NOT support uqmi, it supports only MBIM. It connects OK using this in /etc/config/network: config interface 'WWAN' option proto 'qmi' option device '/dev/cdc-wdm0' option auth 'none' option ipv6 '1' option pincode '1234' option apn 'Provider_APN' option pdptype 'ipv4v6' It then works for 1. Untuk menggunakan QMI Cellular openwrt, install package QMI dan serial port AT yang dibutuhkan. Updated all packages, installed kmod-usb-serial-qualcomm and picocom. notice netifd: LTE I'm using a Quectel EP20 module to connect to a 4G network as fallback connection. 168. scripts/feeds uninstall uqmi scripts/feeds install -p mrhaav uqmi. Here's my configuration from /etc/config/network: config interface 'modem' option proto 'qmi' option Add ipv6 to uqmi openwrt. Except where otherwise noted, content on this wiki is licensed under the following license: → How to use LTE modem in QMI mode for WAN connection. 14. 1 /* -*- Mode: C; tab-width: 4; indent-tabs-mode: nil; c-basic-offset: 4 -*- */ 2 /* 3 * uqmi -- tiny QMI support implementation 4 * 5 * This library is free software; you can redistribute it and/or 6 * modify it under the terms of the GNU Lesser General Public 7 * License as published by the Free Software Foundation; either 8 * version 2 of the License, or (at your option) any later version Dear developers, I am using a Quectel EC25 modem in QMI mode, and I noticed that under LUCI the IP address of the QMI connection is not shown: If I list the interfaces, the IP address is visible in CLI: wwan0 Link root@OpenWrt:/# uqmi -d /dev/cdc-wdm0 --get-data-status "disconnected" root@OpenWrt:/# uqmi -d /dev/cdc-wdm0 --get-data-status "connected" uqmi commands hang. However, testing the speed I have the following phanomenon: DL ~1 Mbit/s UL ~7 Mbit/s This is reproducable. 0 or 23. I've backported this patch to 21. 0 International First go to here and download the latest uqmi_<xxxxxxxxx>_mipsel_24kc. 04. opkg install uqmi_ < xxxxxxxxx > _mipsel_24kc. X but with 23. Now i moved it to Greece and wifi works but no internet/4g working. Based on @cezary comment, I saw that there's no need I forgot to mention that I installed uqmi and luci-proto-qmi using phone as AP and then copying the . An old problem that I had with my B818-263 was that every 48 hours my ISP would require a wan IP refresh of sorts, and the B818-263 would drop the connection to NO-CARRIER, and back (For the sms gateway question check my last message here. More information and source code: https://github. org> 5 * 6 * This library is free software; you can redistribute it and/or 7 * modify it under the terms of the GNU Lesser General Public 8 * License as published by the Free Software Foundation; either 9 * version 2 of the License, or Can not connect to Verizon, using EC25-V. 3 on my TP-Link TL-MR6400 v4. • OpenWrt. Hello I have Archer MR200 with built in Qualcom 4G modem and OpenWRT 19. Surfer2010 May 1, 2022, 1:20pm 1. pid -s /lib/netifd/ OpenWrt 23. timeout parameter is not used in qmi. I am new to Openwrt. com> Signed-off-by: Felix Fietkau <nbd@nbd. 02 (on a TP-Link C7 v2), trying to install package luci-proto-qmi it it tells me "Required dependency package uqmi is not available in any repository. According to memory I've released the client-id (uqmi -d /dev/cdc-wdm0 --release-client-id wds --set-client-id wds,87) and that made it work, if I remember correctly. Here's my config. Is this signal info indicating a good/usable signal ? uqmi -d /dev/cdc-wdm0 --get-signal-info {"type": "lte", 1 /* 2 * uqmi -- tiny QMI support 2014-2015 Felix Fietkau <nbd@openwrt. I am able to use ATI commands over serial, I am able to use uqmi to query the modem (if I disable the interface to prevent connection on boot), however the start network command on line 279 Hello, i'm trying to install a USB 4g dongle on my openwrt 17. Yes, just enable that option in kernel. 2 for uinelec u7628 I have created this version for unielec 7628 from sourcce In previous versions for uqmi I could see pdp-type as ipv4v6 but in this version only ipv4 is displaye Hi all, I am using a Telit LM940 module to have LTE connection. Does someone has an idea what could be the reason for that? root@TL-MR6400:~# uqmi -d /dev/cdc-wdm0 --get-data-status libc, uqmi Categories: luci---protocols Repositories: luci Architectures: If you want to contribute to the OpenWrt wiki, please post HERE in the forum or ask on IRC for access. I have no clue if I've done it right or not. ipk in branch 21. package: uqmi Don´t run other uqmi scripts in parallell. After some investigation, it seems that the uqmi utility doesn't return the correct SIM application as The "wwan" interface, managed by uqmi, is reported as up, yet data transfers don't work. I’ve used LuCi and the QMI protocol in it to configure the thing. SSH to openwrt, transfert the file and install. 0-rc6 Previous message (by thread): [OpenWrt-Devel] Unable to connect with uqmi ("No effect") Next message (by thread): [OpenWrt-Devel] Unable to connect with uqmi ("No effect") Messages sorted by: Carlo Lobrano <c. It is my first-time configuring QMI. Anyway, a call to uqmi -d /dev/cdc-wdm0 --get-data-status shows "disconnected". lacv zwshdmgg fef byksto yarbqcv qmg gosf ddcb gzp hgmtj